Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x. 1.42.2

Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x. 1.42.2

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

1.42.2

22. 06. 2007
  • SW version number corrected.

1.43.4

08. 10. 2010

This software applies to the following DEIF products:

  • Multi-line 2 - EC-1/GC-1

Changes:

  • Status of cable supervision in USW optimised

1.43.3

18. 08. 2009
  • Wire break symbol in Chinese added.

1.43.2

18. 06. 2008
  • Binary inputs with cable supervision updated.

1.43.1

04. 02. 2008
  • Energy counter updated.

1.43.0

15. 01. 2008
  • Multi input wirebreak failclass changed to warning

1.42.3

02. 11. 2007
  • Multiinput wirebreak alarm updated.

1.42.2

22. 06. 2007
  • SW version number corrected.

1.42.1

19. 06. 2007
  • Extended stop updated when using frequency as running feedback.
  • Remote puls start updated during cooldown

1.42.0

14. 05. 2007

New features:

  • New digital input function, remote puls start
  • New digital input function, remote puls stop
  • New relay output function, auto mode indication

Changes:

  • Mode (Auto/Local) is not stored, if power is removed from the controller.

1.41.2

28. 02. 2007
  • Busbar transformer setting updated.

1.41.1

19. 02. 2007

Changes:

  • Engine running relay now reacts to running feedback.
  • Ext stop is now performed when running feedback is lost.
  • Failclass error corrected in Hz / V failure alarm

1.41.0

03. 01. 2007

Changes:

  • Shutdown possibility during start sequence added
  • 4-20 mA input range improved.

1.40.4

01. 10. 2006

Changes:

  • MB open / close feedback updated

1.40.3

22. 08. 2006

Changes:

  • Chinese texts updated.
  • Icons updated.
  • CanOpen remote start/stop updated.
  • Firepump updated with CAN alarm.
  • Alarm relay B updated.
  • Low power readout for USW scaled.
  • Oilpressure readout for USW scaled.
  • PF calculation updated.

1.40.2

21. 03. 2006

Changes:

  • L1-0 error message updated

1.40.1

08. 03. 2006

Changes:

  • Running hour counter updated.
  • MB handling upon power up changed

1.40.0

08. 02. 2006

New features:

  • VDO 3 range increased to 2400 ohm.
  • External heater function added.
  • New stop coil function added - stop coil no start
  • L1-N value error alarm added.
  • Mains failure frequency detection ON/OFF function added.
  • Additional view added.
  • Parameter groups added.
  • GC-1 frequency readings shown with 1 decimal.
  • Power readings shown with 1 decimal if Pnom < 49kW.
  • Diode compensation function added.
  • Test input added for AMF.
  • New digital input texts added.
  • New text "Coolant pressure" added to analog input (4-20mA).
  • External trip of MB added to AMF sequences.
  • Extra password level added.
  • GB breaker delay function added.
  • Oilpressure feedback added.

Changes:

  • Some parameter settings updated.

1.30.5

29. 11. 2005

New features:

  • New AMF situations added.
  • Run status alarm added.

Changes:

  • Fuel pump function updated.
  • Stop coil funciton updated.
  • Input functions updated (Idle run, firepump).
  • Alarm / limit relay functions updated.
  • Default settings updated (Charger gen).
  • Breaker interlock updated.
  • Start enable updated.
  • Parameter menu updated.
  • Setting of voltage transformers updated.
  • Language handling updated.
  • AMF functions updated.
  • VDO user definable inputs updated.
  • Run enable updated.
  • Block (shutdown) updated.
  • HW change to VDO inputs supported.
  • Device number for options in USW updated.

1.30.2

21. 10. 2005

Changes:

  • Tacho feedback updated
  • E counter updated

1.30.1

05. 10. 2005

Changes:

  • Test function updated.

1.30.0

05. 10. 2005

New features:

  • Italian and Chinese language supported.
  • Option H1 (CANopen) added.
  • 1 second delay added to starter and tacho feedback

Changes:

  • Writing of outputs from USW corrected.
  • Cool down timer updated remote mode.

1.20.1

12. 09. 2005

Changes:

  • Test function updated

1.21.0

12. 09. 2005

New features:

  • German, Spanish and French language supported.

Changes:

  • Nominal voltage is phase-phase
  • D+ timer updated
  • Firepump updated
  • "f/U..." texts changed

1.20.0

03. 08. 2005

New features:

  • Support for 3-phase measurementboard (GC-1)
  • Support for option B3 (GC-1 AMF)

1.10.2

04. 07. 2005

Changes:

  • Configurable outputs updated