TDU 107 Extended

TDU 107 Extended

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

1.4.2.1

Corrections

  • Fixed issue with home page application drawing becoming zoomed out with every power cycle or reboot from TDU restart.
  • Fixed issue with TDU not connecting with AGC-4 Mk II application software version 6.14.0.
  • Fixed show/hide of page 2-3 in home.
  • Resolved issue with inhibit start button, inhibit stop button, inhibit GB/TB button and inhibit MB button commands.

1.4.2.1

14. 10. 2024

Corrections

  • Fixed issue with home page application drawing becoming zoomed out with every power cycle or reboot from TDU restart.
  • Fixed issue with TDU not connecting with AGC-4 Mk II application software version 6.14.0.
  • Fixed show/hide of page 2-3 in home.
  • Resolved issue with inhibit start button, inhibit stop button, inhibit GB/TB button and inhibit MB button commands.

1.4.2.0

11. 06. 2024

New features

   1- Confirm action pop-ups.

 

Changes

   1- New method for handling translations.
   2- Tier 4 jump improvements.

 

Corrections

   1- Fixed issue with parameter dialogue not showing the correct state of the toggle switches.

1.4.1.0

04. 01. 2024

New features

        • Support for ASC-150.
          Support for ASC-4

1.4.0.0

26. 10. 2023

New features

      • Supervision variant for TDU.

Changes

      • Extended capability to read more VTA's.

Corrections

      • Fixed issue with TDU not being able to connect to AGC-4 Mk II v6.08.0.
        Fixed issue with TDU not being able to connect to AGC-4 Mk II BTB.

1.3.12.0

25. 08. 2023

New features

    • Supervision shows ASC controllers.

Changes

    • Added support for Volvo EMS.

Corrections

    • Fixed TDU 107 supervision issue.

1.3.11.1

20. 06. 2023

Changes

    • Fixed missing application supervision when there is a BTB controller in the application drawing.

1.3.11.0

05. 03. 2023

New features

  • Added support for FPT stage V engines.

Changes

  • Created separate pages for "Engine lamps" and "Exhaust aftertreatment".
  • Added support for tree view translations.
  • Made opening parameters more intuitive.

1.3.10.1

07. 10. 2022

Corrections:

1- Fixed horizontal scrolling of Supervision.
2- Fixed missing "None" option in "Instrument Selection".
3- Fixed missing Custom Logo in "Log" and "Controller settings" pages.
4- Reset index when changing between "Controller settings" lists.

1.3.10.0

13. 07. 2022

Changes:

  • Logo implementation and top bar branding.
  • Branding configuration import and export.

Corrections:

  • Fixed glitch with negative values in alarm and event log.
  • Fixed glitch with controller communication lost for 1-2 seconds every 13 or 25 minutes.
  • Fixed glitch with TDU not able to connect to AGC-4 Mk II Mains controller.

1.3.9.1

17. 02. 2022

Changes:

  • Only show measurements supported by the connected ECU.

Corrections:

  • Fixed issue with writing alarm settings for parameters

1.3.9.0

12. 01. 2022

Changes:

  • New application select page added to the setup menu.

Corrections:

  • Toggle switches are more accurate now.
  • Fixed language export issue with empty AOP labels.
  • Fixed missing semi button when activating the German AUS mode.

 

1.3.8.0

06. 12. 2021

Changes:

  • Added option to hide application and nominal settings on instrument pages.
  • New and updated customer branding.

Corrections:

  • IP can't be changed when disabling Master/slave when TDU is connected to slave.

1.3.7.0

31. 05. 2021

New features:

  • Support for OEM product IDs in AGC-4 Mk II is added.
  • Scania EMS S8 support is added.
  • Block mode button is added.
  • Master/slave controller manual switch is added.

Changes:

  • "AUS" mode for German option V0108 in "Auto" and "Test" mode is added.

Corrections:

  • Alarms are removed from the header when alarm conditions disappear.
  • Fixed an issue with missing genset modes in the language file.
  • Fixed that the genset mode would change if the password level was set to service or master.

1.3.6.0

23. 03. 2021

New features:

  • Added support for OEM product IDs in AGC-4 Mk II.
  • Extra safety pop up (Nominal setting + Plant mode).
  • Translation file added with "TDU specific texts".
  • "UpdatePackage.zip" includes software version.
  • Support updatepackage.zip with lower case characters.

1.3.5.0

29. 01. 2021

New features:

  • Added support for AGC-4 Mk II
  • Added customer branding

1.3.3.0

10. 09. 2020

Supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.
Recommended minimum AGC-4 SW: 4.76.1.

New features:

  •    Further brandings are added.
  •    AGC-4 as clock master is added.

Changes:

  •    New entry point for the ECU measurement window is added.

Corrections:

  •    Parameter max. value was not taken into account for text values.
  •    If exactly 9 alarms were present, the last one was not visible.
  •    Possibility to include system information when exporting a TDU.config file is added.
  •    Preventive measures were taken to stabilize the VNC connection.
  •    Generator measurements are removed from mains TDU.
  •    Regeneration parameters are added to TDU.
  •    Application supervision now supports mains with id´s 1-16 and DG´s with ID 17-32.

1-3-2-0

17. 06. 2020

Supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.
Recommended AGC-4 SW: 4.76.1.

New features:

  • EIC measurements can now be seen in a separate window.
  • Added support for new Boolean measurements.

Changes:

  • More texts have been included in the translation file, to extend translation capabilities of the TDU. (Controller texts and Engine DM1/DM2 texts).
  • Sync shortcut on the home screen now only requires a single press instead of a long press.
  • Internal references to measurement layout on Modbus have been updated.
  • Preferred font have been removed from the CSV file.

Corrections:

  • Current status of the DG on the alternator curve now works properly.
  • TDU Supervision is now updated correctly when using the Easy connect feature.
  • Empty AOP texts are now saved during power cycle or in TDU.config files.
  • "Autojump to sync scope" is now saved during power cycle or in TDU.config files.
  • The screensaver now shows the "Connection lost" message.
  • The branded splash screen is now shown correctly.

1.3.1.0

19. 02. 2020

Supported on AGC-4 DG & AGC-4 Mains.
AGC-4 SW required: 4.76.1.

New features:

  •    Control panel instruments can now be custom scaled by pressing and holding for 3 seconds.
  •    All voltage selections in parameter 9030 are now supported.
  •    Access lock implemented; when the input is configured and active in the controller all settings are read only in the TDU.
  •    New screen is added with current measurements shown graphically.
  •    M-logic command "Inhibit. mode button" is now reflected in the TDU.
  •    It is now possible to add a separate password for control panel instruments under "Permissions".
  •    Fuel level is now shown in the top bar, if parameter 10980, 10990 or 11000 is set to "RMI fuel level" via the utility software.
  •    Running hours is now shown in the top bar, if connected to a genset controller.
  •    Parameter shortcut is added on the control page; it can be enabled/disabled under "Display settings".
  •    Power Management ID and priority are added to the home screen, when connected to a genset controller.
  •    Auto Jump to Synchroscope page is added; it can be enabled/disabled under "Display settings".
  •    Import/ Export: It is now possible to load a configuration file from an older software version.

Changes:

  •    20 pages are now available in the instrument panels on the control page.
  •    Lists of instrument measurements have been expanded.
  •    User access level filtering on the parameter page have been removed.
  •    DM1/DM2 texts have been expanded.
  •    When connected to a German AGC-4 with V0108 option, the manual button is removed.

Corrections:

  •    Language management create export has been corrected, when specific German characters are used in the controller translation.
  •    Visibility of the DM1 top icon has been corrected.

1.3.0.1

23. 09. 2019

Only supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.

Corrections:

  • Corrected: AOP shortcut on control panel page.
  • When changing mode, the confirmation dialogue now always pops up.

1.3.0.0

12. 09. 2019

Supports AGC-4 DG & AGC-4 Mains controllers.
Minimum AGC-4 SW required: 4.74.3.

New features:

  • Support of AGC-4 mains controller.
  • Import/export of following settings via USB:
            - Meters on homepage
            - Password levels
            - AOP texts
            - All settings under "Display config" 
  • Added "Connection to controller" text on start-up screen.

Changes:

  •    TDU backlight timeout introduced.
  •    Fixed sporadic communication timeout messages on TDU.
  •    Extended number of status texts on the TDU.

Corrections:

  • Fixed screensaver freeze issue.
  • Corrections to some status texts.
  • Fixed rare initial communication issues.
  • Create new master language function corrected

1.2.2.0

19. 06. 2019

Only supported on AGC-4 DG.
Minimum AGC-4 SW required: 4.72.0.

Changes:

  • Internal production handling updated.

1.2.1.0

12. 06. 2019

Only supported on AGC-4 DG.
Minimum AGC-4 SW required: 4.72.0.

New features:

  • Implementation of offline USB update of TDU
  • Added scrolling on supervision page
  • Added hardcoded master password to DM1/DM2 clear button
  • Enhanced user feedback during restart of TDU
  • Added new EasyConnect text: "DG Ready to be added"

Changes:

  • Improved connection stability between TDU and AGC-4 controller
  • Change scaling of Fuel rate measurement

Corrections:

  • Correct Modbus offset for escape mode timer
  • Improved stability of auto connect feature
  • Added missing password prompt to AOP shortcut on home screen
  • Fixed misplaced buttons in control panel

DEIF 제품을 완전하게 활용하기 위해서는 DEIF에서 제공하는 업데이트를 설치하도록 항상 권장하고 있습니다.

업데이트된 소프트웨어는 언제나 무료로 www.deif.com의 “소프트웨어”에서 “소프트웨어 내려받기”를 통해 내려받기할 수 있습니다.

질문 또는 제품 관련 소프트웨어에 관한 문의는 DEIF A/S +45 96149614 또는 해당 지역의 DEIF 사무소로 연락해 주시기 바랍니다. 그 외에도, support@deif.com로 이메일을 보내 주시면 언제든지 도와드릴 준비가 되어 있습니다.