iE 250 Application Software

iE 250 Application Software

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

2.0.7.2

Minimum required version of PICUS: 1.0.23.0

Corrections

  • EIC start/stop now works on all protocols. Small fixes made to CAT7.1.
  • Fixed issue where display preferences were not stored during power cycle.
  • Fixed issue where display did not exit dimmed state.
  • Fixed issue where Web.config was not bundled correctly in the RAUC bundle.
  • Implemented Yanmar Stage V regeneration acknowledge lamp.

2.0.7.2

02. 12. 2024

Minimum required version of PICUS: 1.0.23.0

Corrections

  • EIC start/stop now works on all protocols. Small fixes made to CAT7.1.
  • Fixed issue where display preferences were not stored during power cycle.
  • Fixed issue where display did not exit dimmed state.
  • Fixed issue where Web.config was not bundled correctly in the RAUC bundle.
  • Implemented Yanmar Stage V regeneration acknowledge lamp.

2.0.7.1

07. 11. 2024

Minimum required version of PICUS: 1.0.22.0

New features

  • EIC: Added a parameter to configure TSC1 destination address.
  • Added EIC protocol Yanmar Stage V.
  • Added EIC protocol Jichai JC15T JG.

Corrections

  • TSC1 corrected for Caterpillar, Perkins, Iveco Vector8 and John Deere. VP70 source address corrected for Volvo Penta EMS2 and EMS2.3.
  • EIC: Ash load percentage is available on Modbus and the display.
  • Fixed issue where screen was white on startup.
  • EIC: Corrected frequency selection for Volvo Penta EMS 2.4.

2.0.4.1

11. 07. 2024

Minimum required version of PICUS: 1.0.22.0

New features

  • An alarm has been added to inform the customer if the log system on the controller has been damaged or is in any other way malfunctioning. This is done to comply with Security Log Management requirements.
  • Updated Volvo EMS2.4 to support ACM module.
  • EIC: Added support for CAT C7.1.
  • EIC: Added support for Kohler KDI3404.

Corrections

  • Fixed default value for the regulator status text.
  • Added support for adjusting the brightness level on the controller.
  • Fixed visibility of ECU and CAN parameters.
  • Fixed issue where Custom Logic was missing.
  • Fixed issue where the licence error alarm could occur after a restore from a backup.
  • Name of Modbus protocols, as seen in PICUS, now includes both type and variant, rather than only type. For example, 'Single Genset GB MB' rather than only 'Single Genset'.
  • Fixed issue where disclaimer was incorrectly shown.

2.0.1.0

03. 04. 2024

This software package consist of:

  • One single file which contains the entire application SW for the controller

 

To be used with at the least PICUS version 1.0.21.0

 

New features:

• Added a navigation item linked to CODESYS Webvisu allowing a seamless transfer to the WebVisualization page.

 

Corrections:

• Corrected issue where the "Communication settings changed" alarm was incorrectly triggered.
• Corrected the menu structures in the display menu.
• Corrected inconsistent configuration of network and port settings in the browser configuration tool.

2.0.0.1

23. 02. 2024

This software package consist of:

  • One single file which contains the entire application SW for the controller

 

To be used with at the least PICUS version 1.0.21.0

 

Changes:

Changed SSH service to OFF by default.

 

Corrections:

-Corrected an issue in emulation causing the controller to restart.
-Corrected the naming of the action choices for the "CAN fail mode alarm".
-Corrected reactive energy unit from kvar to kvarh.
-Corrected an issue causing the DEF level to not be shown by default on the Exhaust after-treatment dashboard.
-Corrected an issue causing the auto-jump to the Exhaust after-treatment dashboard not to work.
-Corrected an issue on the Exhaust after-treatment dashboard where the engine lamps would not appear when transitioning directly from N/A to ON.

 

2.0.0.0

06. 02. 2024

This software package consist of:

  • One single file which contains the entire application SW for the controller

 

To be used with at the least PICUS version 1.0.21.0

 

New features:

• Initial release

 

 

DEIF 제품을 완전하게 활용하기 위해서는 DEIF에서 제공하는 업데이트를 설치하도록 항상 권장하고 있습니다.

업데이트된 소프트웨어는 언제나 무료로 www.deif.com의 “소프트웨어”에서 “소프트웨어 내려받기”를 통해 내려받기할 수 있습니다.

질문 또는 제품 관련 소프트웨어에 관한 문의는 DEIF A/S +45 96149614 또는 해당 지역의 DEIF 사무소로 연락해 주시기 바랍니다. 그 외에도, support@deif.com로 이메일을 보내 주시면 언제든지 도와드릴 준비가 되어 있습니다.